Architecture Design

Saswati Swami (sswami@eden.rutgers.edu)

Introduction

The current NodeHandler code works satisfactorily on the small grid and the sandboxes. But this same code fails to work correctly on the big grid. This is due to the fact that in the current grid consisting of 400 nodes, packet loss is a major problem. And this problem escalates sharply with the increase in the no. of nodes. Specifically, when trying to image more than 150 nodes in a single attempt, the high packet loss prevents successful completion. To alleviate this problem, it has been decided to explore the use of broadcast instead of multicast.

Major Design Requirements

R.1:

It has been decided that all communications from the NodeHandler to the NodAgent will be 
through broadcast and that all feedbacks from the NodeAgent to the NodeHandler will be sent 
through TCP. This is because then

- reliable feedbacks can then be ensured, 
- explicit control over the feedback message content can be allowed,
- integrating the feedback messages with the existing message processing code in the 
  NodeHandler will be easier e.g. sequence id correlation, etc,
- existing messages being sent from the NodeAgent to the NodeHandler can be modified to 
  serve the dual purpose of providing feedbacks too.

R.2:

All communication will be handled in the communication layer which will be a separate process.
The present focus is on exploring reliable communication with minimum packet loss and once this 
issue is resolved, the issues pertaining to converting this process into a loadable library 
will be addressed to.

This will need changes to the communication layer in both the NodeHandler and the NodeAgent. 

R.3:

The communication layer will use two separate approaches, one for sending messages and the 
other for receiving messages. Messages being sent from the NodeHandler to the NodeAgent will 
use broadcast. A single message will be broadcast by the NodeHandler and this message will be 
received by all the NodeAgents. 

Messages being received from the NodeAgent will be use TCP. The NodeAgent communication layer 
will be modified to send all messages to the NodeHandler using TCP. 

R.4:

The messages sent from the NodeHandler to the NodeAgent consist of commands to be executed on
the NodeAgent. Since the communication layer will broadcast the message to all the nodes, the 
NodeAgents will have the filters to deteremine whether a message is to be accepted / rejected.
 Current NodeAgent code has such filters and these will be enhanced only if necessary.

After a message is sent, the communication server will wait for ACKs from the NodeAgent, which
will be received through the TCP socket. All message-ACK correlation for each node will be 
done by the communication server. Also, it will, after a pre-defined interval, repeatedly send 
the command till it receives an ACK confirming receipt of a previously sent message from all 
the intended nodes. Only after all the NodeAgents have confirmed successful receipt of the 
command, will the communication server initmate the NodeHandler to proceed with sending the 
next command. 

R.5:

The communication layer will initially be a separate server that is running the reliable 
multicast protocol. It will also handle all TCP socket related functions. This separation of 
processes will help in isolating and subsequent easy resolution of all communication related 
issues. The IPC mechanism between this server and the NodeHandler will be implemented using 
pipes. When the NodeHandler wants to send a message to the NodeAgent, this message will be 
piped to the server which will then send the message using multicast. Again, when a message is 
received from the NodeAgent by this server, it will pipe this message to the NodeHandler. 

Later this separate server can be combined with the NodeHandler as a loadable library if there 
are no significant performance issues found.

R.6:

The communication server will not pipe the heartbeats from the NodeAgents to the NodeHandler. 
Instead, it will keep track of these messages on a per-node basis and on detecting a breakdown
 in communication; it will send a RETRY message to the NodeAgent. The NodeAgent will consider 
it to be a message from the NodeHandler.

R.7:

All issues relating to scaling impacts on the decision to use TCP will be thoroughly 
investigated. TCP is a quick way for us to not think of reverse path reliability. Once we get 
to proper scaling on the forward path, we will switch to UDP, if necessary. We might also 
implement some scheme to prioritize the messages.

Overall Architecture

Software Design

Algorithm for NodeHandler Communication Server

The NodeHandler on startup will open the required pipes and then fork the Communication Server process. The Communication Server is a 2-threaded process. Following is the algorithm for this process functionality:

1.  
2. 

See Also

​http://www.orbit-lab.org/wiki/Internal/DesignNotes