== Exercise 2: Measuring Performance of a MobilityFirst Router == === Objective === In this exercise, we will try to drive synthetic traffic through the router and measure key performance characteristics such as throughput and forwarding latency. Since MobilityFirst presents a hop-by-hop block data transport, we can vary the unit size of the data block and observe it's impact on the performance. We will also try to visualize the performance results using OMF's result service by installing an OML-enabled monitor on the routers. === Deploy the Network === This tutorial assumes that a 4 nodes topology has been already established in one of the Orbit sandboxes or the grid: {{{ #!sh Host (GUID 101) ---- MFR1 (GUID 1) ---- MFR2 (GUID 2) ---- Host2 (GUID 102) }}} [[CollapsibleStart(If not coming from the previous exercise follow these instructions to setup your network)]] Once logged into the grid console: {{{ #!sh ssh username@console.grid.orbit-lab.org }}} From the console we will start by loading the Mobilityfirst image into the four nodes that have been assigned to you: {{{ #!sh omf load -i 'mf-release-latest.ndz' -t system:topo:mf-groupX }}} '''system:topo:mf-groupX''' represents the group of 4 nodes and '''mf-groupX''' has to be replaced by the group id assigned to you. For example, '''mf-group1''' will load the image on nodes 'node1-1,node1-2,node2-1,node2-2' If the output of your console looks similar to: {{{ #!sh INFO exp: ----------------------------- INFO exp: Imaging Process Done INFO exp: 4 nodes successfully imaged - Topology saved in '/tmp/pxe_slice-2014-10-15t02.10.16.594-04.00-topo-success.rb' INFO exp: ----------------------------- INFO EXPERIMENT_DONE: Event triggered. Starting the associated tasks. INFO NodeHandler: INFO NodeHandler: Shutting down experiment, please wait... INFO NodeHandler: INFO NodeHandler: Shutdown flag is set - Turning Off the resources INFO run: Experiment pxe_slice-2014-10-15t02.10.16.594-04.00 finished after 1:50 }}} your nodes have been imaged correctly. === Deploy Network === Software and experiment control in the ORBIT testbed can be automated greatly using the OMF framework. An OMF control script is written in Ruby and allows the experimenter to specify the set of nodes, their network configuration, to specify software components and arguments, and to control their execution on one or more nodes. We will use an OMF script to bring up 4 ORBIT nodes to host our topology, with corresponding software components. We will first introduce the main details of the scripts that will be run and then will step to the execution itself. ==== Software Component Specification ==== The following snippet shows the specification of the MobilityFirst router along with the required arguments: {{{ #!ruby defApplication('MF-Router', 'router') {|app| app.shortDescription = "Click-based MobilityFirst Access Router" app.path = "/usr/local/src/mobilityfirst/eval/orbit/tutorial/scripts/ARWrapper.sh" # click options app.defProperty('num_threads', 'number of threads', "-t",{:type => :integer, :mandatory => true, :default => 4, :order => 1}) app.defProperty('ctrl_port', 'port for Click control socket', "-c",{:type => :integer, :order => 2}) # click config file app.defProperty('config_file', 'Click configuration file', "-C",{:type => :string,:mandatory=> true}) # keyword parameters used in click config file app.defProperty('my_GUID', 'router GUID', "-m",{:type => :string, :mandatory => true}) app.defProperty('topo_file', 'path to topology file', "-f",{:type => :string, :mandatory => true}) app.defProperty('core_dev', 'core network interface', "-d",{:type => :string,:mandatory => true}) app.defProperty('GNRS_server_ip', 'IP of local GNRS server', "-s",{:type => :string,:mandatory => true}) app.defProperty('GNRS_server_port', 'Port of GNRS server', "-p",{:type => :string,:mandatory => true}) app.defProperty('GNRS_listen_ip', 'IP to listen for GNRS response', "-i",{:type => :string,:default => "0.0.0.0"}) app.defProperty('GNRS_listen_port', 'port to listen for GNRS response', "-P",{:type => :string,:default => "10001"}) app.defProperty('edge_dev', 'edge network interface', "-D",{:type => :string,:mandatory => true}) app.defProperty('edge_dev_ip', 'IP assigned to edge interface', "-I",{:type => :string,:mandatory => true}) } defApplication('MF-GNRS', 'gnrs') {|app| app.shortDescription = "GNRS Server" app.path = "/usr/local/src/mobilityfirst/eval/orbit/tutorial/scripts/GNRSWrapper.sh" app.defProperty('log4j_config_file', 'log 4j configuration file', "-d",{:type => :string, :order => 1}) app.defProperty('jar_file', 'server jar file with all dependencies', "-j" ,{:type => :string, :mandatory=> true, :default => "/usr/local/src/mobilityfirst/gnrs/jserver/target/gnrs-server-1.0.0-SNAPSHOT-jar-with-dependencies.jar", :order => 2}) app.defProperty('config_file', 'server configuration file', "-c",{:type => :string, :mandatory=> true, :order => 3}) } #Enable OML reporting by default defApplication('MF-HostStack', 'hoststack') {|app| app.shortDescription = "MF host network stack" app.path = "/usr/local/bin/mfstack" app.defProperty('log_level', 'log level', nil,{:type => :string, :mandatory => true, :order => 1, :default => "-e"}) # default is 'error' app.defProperty('config_file', 'stack configuration file', nil,{:type => :string, :mandatory => true, :order => 2}) } }}} As seen above, the router is configured with both 'core' and 'edge' interfaces. The core interfaces connect routers towards the core of the network, while the edge interface enables hosts to connect and access the MobilityFirst network. Also seen above is the GNRS service related arguments that specify which server (IP and port) the router should use for in-network name resolution purpose, both for sending requests and to receive responses. By default it will listen on all interfaces and port 10001. ==== Setting up the Software Node Groups ==== The following shows how the node groups for the routers are setup in the OMF control scripts. Node groups allows experimenters to use single statements to set configuration and execute commands across all nodes in the group. {{{ #!ruby for i in 1..num_routers defTopology("topo:router_#{i}") { |t| aNode = routersTopo.getNodeByIndex(i-1) t.addNode(aNode) info aNode, " assigned role of router with GUID: #{i}" } defGroup("router_#{i}", "topo:router_#{i}") {|node| node.addApplication('MF-Router') {|app| app.setProperty('num_threads', router_threads) app.setProperty('config_file', click_conf) app.setProperty('my_GUID', router_guid[i-1]) app.setProperty('topo_file', rtr_topo_file) app.setProperty('core_dev', core_dev) app.setProperty('GNRS_server_ip', GNRS_server_ip) app.setProperty('GNRS_server_port', GNRS_server_port) app.setProperty('GNRS_listen_ip', "192.168.100.#{i}") app.setProperty('GNRS_listen_port', GNRS_listen_port) app.setProperty('edge_dev', edge_dev) app.setProperty('edge_dev_ip', router_ether_if_ip[i-1]) } #If is the first router add the GNRS if i == 1 aNode = routersTopo.getNodeByIndex(i-1) info aNode, " will also host the GNRS server" node.addApplication('MF-GNRS') {|app| app.setProperty('log4j_config_file', GNRS_log_file) app.setProperty('jar_file', GNRS_jar_file) app.setProperty('config_file', GNRS_conf_file) } end node.net.e0.ip = "192.168.100.#{i}" node.net.e0.netmask = '255.255.255.0' node.net.w0.mode = "adhoc" node.net.w0.type = 'g' node.net.w0.channel = "11" node.net.w0.essid = "SSID_group_#{i}" node.net.w0.ip = "192.168.#{i}.1" } end #Create host groups for i in 1..num_hosts defTopology("topo:host_#{i}") { |t| aNode = hostsTopo.getNodeByIndex(i-1) t.addNode(aNode) info aNode, " assigned role of client with GUID: #{100 + i}" } defGroup("host_#{i}", "topo:host_#{i}") {|node| node.addApplication('MF-HostStack') {|app| app.setProperty('config_file', hoststack_conf_file[i-1]) app.setProperty('log_level', log_level) } #node.net.e0.ip = "192.168.#{i}.#{i+100}" #node.net.e0.netmask = '255.255.255.0' node.net.w0.mode = "adhoc" node.net.w0.type = 'g' node.net.w0.channel = "11" node.net.w0.essid = "SSID_group_#{i}" node.net.w0.ip = "192.168.#{i}.2" } end }}} As can be seen above, properties which were defined in the MF-Router, MF-GNRS and MF-HostStack applications have been set here. Moreover, node interfaces have been set up, and IP addresses have been assigned to them. As we discussed earlier the router is configured with both edge and core interfaces. The ethernet interface is used to connect to the core of the network, and the wireless interface is for connection to the clients. On the other side, the client is equipped with wifi interface to connect to the access router. [[CollapsibleEnd]] We will assume the network described and initialized in Exercise 1 is up and functional. Here also we will use mfping to send packets between the hosts. In addition to the deployment specified in exercise 1, we install OML-enabled statistics monitor for MobilityFirst routers. The entire script is available as part of the tutorial package as orbit/tutorial/scripts/exercise2.rb The key extensions over previous script are briefly discussed below. ==== Setting up the 'OML enabled Monitor on Routers Application' ==== The following snippet from the script shows the code added to set up the OML enabled Monitor on Routers Application and its arguments: {{{ #!ruby defApplication("mf_click_monitor", "mf_click_monitor") do |app| app.shortDescription = "OML enabld statistics monitor for MobilityFirst Routers" app.path = "/usr/local/bin/mf_click_mon" app.defProperty('ctrl_port', 'Port for Click control socket', nil,{:type => :string, :mandatory => true, :order => 1}) app.defProperty('self-id', 'OML ID', nil,{:type => :string, :mandatory => true, :order => 2}) app.defProperty('oml-config-file', 'OML configuration file', "--oml-config",{:type => :string,:mandatory=> true}) app.defProperty('oml-domain', 'OML domain name', "--oml-domain",{:type => :string,:mandatory=> true}) end self_id = "MonitorID" oml_config_file = "/usr/local/src/mobilityfirst/eval/orbit/tutorial/conf/click-oml-config.xml" oml_domain = "#{Experiment.ID}" defGroup("router_monitors", "router_universe") {|node| node.addApplication('mf_click_monitor') {|app| app.setProperty('ctrl_port', router_control_port) app.setProperty('self-id', self_id) app.setProperty('oml-config-file', oml_config_file) app.setProperty('oml-domain', oml_domain) } } }}} As seen above, the OML enabled monitor will work with the MobilityFirst router that will enable us to track and visualize the forwarding performance of MFRs. In order report statistics to the OML server, the monitor periodically queries the monitor through the control port (''ctrl_port'' in our script) ==== Running the Benchmark Application ==== To generate the traffic that will be reported by the routers, we will use the same ''mfping'' application as in the previous exercise. First of all, you will need to start the experiment via the OMF script. Download the script to the orbit console: {{{ #!sh wget www.winlab.rutgers.edu/~bronzino/downlaods/exercise2.rb }}} Once the file has been downloaded, execute it with the following command: {{{ #!sh omf exec exercise2.rb }}} The following snippet shows how the exercise runs. As indicated above first we will run mfping between the hosts as described in exercise 1: [[CollapsibleStart(If not coming from the previous exercise follow these instructions to run mfping)]] Once the host and router components are up, you can log in to the sender (host identified by GUID 101) and receiver (host identified by GUID 102) host nodes (two separate terminals) and run the 'mfping' application. Run the mfping 'server' specifying the application GUID: {{{ #!sh mfping -s -m 102 -o 101 }}} where "-s" specifies that the host is running as server, "-m" specifies the source guid and "-o" the destination one To run the mfping 'client' {{{ #!sh mfping -c -m 101 -o 102 -n 10 }}} Where "-c" specifies the client is running and "-n" specifies the number of pings between the two nodes. If successfully executed, the client will display some information similar to the following snippet {{{ #!sh root@node1-1:~# mfping -c -m 101 -o 102 -n 10 64 bytes received: seq_n=0, time=25.1470 msec 64 bytes received: seq_n=1, time=23.7070 msec 64 bytes received: seq_n=2, time=20.0559 msec 64 bytes received: seq_n=3, time=24.0371 msec 64 bytes received: seq_n=4, time=23.1831 msec 64 bytes received: seq_n=5, time=20.3069 msec 64 bytes received: seq_n=6, time=24.1379 msec 64 bytes received: seq_n=7, time=19.6230 msec 64 bytes received: seq_n=8, time=20.3931 msec 64 bytes received: seq_n=9, time=20.2239 msec }}} [[CollapsibleEnd]] ==== Visualizing the Performance Data ==== '''Method 1:''' OMF framework supports a result service that allows experimenters to query data stored using the OML measurement framework. The query is performed over the web and requires that you know the hostname and port where the result service runs, and the ''experiment ID'' associated with this experiment - this is obtained from the output following the execution of the control script. It should look something like this : {{{ #!sh Experiment ID: default_slice-2014-10-15t02.12.19.869-04.00 }}} The result service supports either dumping of the entire database or a SQL-like querying option to selectively retrieve required measurement data. The below HTTP request shows an example query to retrieve the reported statistics from the OML enabled monitor for MobilityFirst Routers: {{{ #!sh wget "http://:/result/dumpDatabase?expID=testing_slice-2010-09-03t09.41.43+10.00" -O msg_out.csv }}} Which in our case the hostname is "oml.orbit-lab.org" and the port number is "5054". So the command will look like : {{{ #!sh wget "http://oml.orbit-lab.org:5054/result/dumpDatabase?expID=default_slice-2014-10-15t00.36.59.743-04.00" -O msg_out.csv }}} Note that the URL used in wget, in particular the arguments, may require to be encoded to unambiguously represent special characters when using the HTTP protocol. The downloaded data can now be easily visualized using a tool such as gnuplot. You can find a helper script in the tutorial package that plots they key performance data downloaded using the above query. '''Method 2:''' Alternatively, the performance data may also be visualized using ''omf-web'', OMF's web-based visualization service. It also works in concert with the result service referenced in Method 1, and makes available a variety of graph widgets to visualize live-experiment data logged using OML. Detailed documentation on the installation and usage of omf-web can be found on the [https://github.com/mytestbed/omf_web omf-web github site]. Since this is installed on all ORBIT domains, we will only concern ourselves with defining the widget configuration required to bring up the live graphs for the performance data we are logging. Below is the contents of the simple two widget configuration file available with this tutorial package: {{{ #!yaml title: MobilityFirst Data Transfer Performance # Port number the omf-web service should run at port: 4041 # Root url of AM result2 service result2_server: http://oml:5054 # Define tabs, widgets for visualisation below # tabs: # Data transfer throughput mfperf_tput: # Line chart widget, need to define columns in mapping section. - name: OML TS SERVER type: line_chart data: msg_out mapping: # x-axis, y-axis and group_by. x: ts y: kbytes_per_sec group_by: oml_sender_id mfperf_rtt: # Line chart widget, need to define columns in mapping section. - name: OML TS SERVER type: line_chart data: msg_out mapping: # x-axis, y-axis and group_by. x: msg_length y: transfer_time group_by: oml_sender_id }}} To bring up the visualization, start the basic omf-web service with the configuration file argument: {{{ #!sh omf-web-basic -c }}}