== Full-Duplex Wireless using USRP N210 ==

=== Description ===
In this tutorial, we'll use node11-10 in the main grid (equipped with a USRP N210) to transmit and receive a single frequency over the air to demonstrate full-duplex wireless capability using the Columbia [http://flexicon.ee.columbia.edu/ FlexICoN]'s Gen-1 Frequency-Flat Amplitude- and Phase-based RF Canceller. Pictures of the FlexICoN RF canceller and node11-10 in the main grid equipped with full-duplex capability are below:
 ||||  Figure 1: The ORBIT-FlexICoN Full-Duplex Node  ||
 || [[Image(FlexICoN-gen1-canceller.jpg, 300px)]] || [[Image(FlexICoN-gen1-node11-10.jpg, 400px)]] || 
 ||  (a) The FlexICoN RF Canceller  ||  (b) Full-Duplex SDR at node11-10 in the ORBIT grid  ||

==== Paper ====
For more information, please read:

''T. Chen, J. Zhou, N. Grimwood, R. Fogel, J. Marasevic, H. Krishnaswamy, and G. Zussman, “Demo: Full-duplex Wireless based on a Small-Form-Factor Analog Self-Interference Canceller,” in Proc. ACM MobiHoc'16, 2016.'' [http://wimnet.ee.columbia.edu/wp-content/uploads/2016/06/full_duplex_demo_mobihoc16.pdf (PDF)] [https://dl.acm.org/citation.cfm?id=2942397&CFID=829383168&CFTOKEN=81447061 (DOI)]

Please cite the above paper if you are using the hardware. Please email Tingjun Chen (tingjun [at] ee.columbia.edu) if you are using (or plan to use) the full-duplex node, or if you have any questions. We also thank Mahmood Baraani Dasterjerdi for his contributions.

==== Supports ====
This project is supported by NSF grant ECCS-1547406, DARPA RF-FPGA program, the People Programme (Marie Curie Actions) of the European Union’s Seventh Framework Programme (FP7/2007-2013) under REA grant agreement no [PIIF-GA-2013-629740].11, and a Qualcomm Innovation Fellowship.


=== Hardware / Software Resources Utilized ===
1. The Columbia FlexICoN Gen-1 RF Canceller, which is a frequency-flat amplitude- and phase-based RF canceller implemented using discrete components on a PCB. The Gen-1 RF canceller is optimized to have a center operating frequency at 900MHz.
2. USRP N210 with node11-10 in the ORBIT main grid.
3. [http://www.xdimax.com/sub20/sub20.html SUB-20] is a multi-interface USB adapter for providing popular interfaces between PC (USB host) and different hardware devices. Specifically, we use the SUB-20 SPI module to control and configure the Gen-1 RF canceller (see Fig. 1(a)). The user manual can be found [http://www.xdimax.com/sub20/doc/sub20-man.pdf here].
4. [https://github.com/EttusResearch/uhd, UHD] is already installed with the imaged SDR node.
5. The {{{Eigen C++}}} Library is used for basic algebra used in channel estimation and digital self-interference cancellation. The Eigen releases can be found on the [http://eigen.tuxfamily.org/index.php?title=Main_Page this website]. We used the latest stable release Eigen 3.3.4 through our testings and experiments.

All the source code is also publicly available at [https://github.com/Wimnet/flexicon_orbit here].

=== Set Up ===
Before you can access the testbed, you need to [https://www.orbit-lab.org/schedule make a reservation] and get it approved by the [wiki:Documentation/Scheduler reservation service]. After receiving the reservation's confirmation (approval) email:

 * Login into reserved domain: {{{ssh username@conslole.grid.orbit-lab.org}}}
 * Make sure that the full-duplex node is powered down for loading the desired image: {{{omf tell -a offh -t node11-10}}}
 * Load an image on the node (this process can take about a few minutes so please be patient): {{{omf load -i flexicon-orbit-v1.ndz -t node11-10}}}
 * Turn on the node: {{{omf tell -a on -t node11-10}}}
 * Login into the node: {{{ssh root@node11-10}}}
 After login into the node, a {{{flexicon_orbit}}} folder should exist under the home directory of {{{node11-10:~/}}} which contains the source code of this example. You can always retrieve the most recently updated code from [https://github.com/Wimnet/flexicon_orbit here].


=== Run the Experiments ===
You will need to login into the full-duplex node (by {{{ssh root@node11-10}}}) in two separate terminal windows lo for running the experiment: one for the main full-duplex transceiver UHD program and one for controlling the RF canceller.

==== In Terminal 1 (UHD) ====
 * Build the example (this is already done in the loaded image):
{{{
cd ~/flexicon_orbit/fd_transceiver_simple/uhd/
mkdir build
cd build
cmake ../
make
}}}
 * Configure the USRP Ethernet interface: {{{ifconfig eth2 192.168.10.1 netmask 255.255.255.0 up}}}
 * Check the conection and serial number of the USRP N210: {{{uhd_find_devices}}}. The serial number should be {{{F331D4}}}.
 * Run the example with IQ rate {{{rate}}}, carrier frequency {{{freq}}}, TX gain {{{tx-gain}}}, and RX gain {{{rx-gain}}}:
{{{
cd ~/flexicon_orbit/fd_transceiver_simple/uhd/build/
./fd_transceiver_simple --tx-args="serial=F331D4" --rx-args="serial=F331D4" --rate 1e6 --freq 900e6 --tx-gain 0 --rx-gain 10
}}}
 The default sine wave has an amplitude {{{ampl=0.3}}} and wave frequency of 100kHz {{{wave-freq=100e3}}}, which corresponds to a 0dBm TX power level. This terminal window will show the power level at RX baseband, after RF cancellation (before digital) and after digital cancellation, respetively. The UHD program is calibrated with {{{--rx-gain=10}}}, other RX gain values may results in inaccurate power level computation.
 * An example temrinal output is below:
{{{
root@node11-10:~/flexicon_orbit/fd_transceiver_simple/uhd/build# ./fd_transceiver_simple --tx-args="serial=F331D4" --rx-args="serial=F331D4" --rate 1e6 --freq 900e6 --tx-gain 0 --rx-gain 10
linux; GNU C++ version 4.8.4; Boost_105400; UHD_003.010.001.001-0-unknown


Creating the transmit usrp device with: serial=F331D4...
-- Opening a USRP2/N-Series device...
-- Current recv frame size: 1472 bytes
-- Current send frame size: 1472 bytes

.
.
.

Press Ctrl + C to stop streaming...

TX Stream time was: 0 full secs, 0.100064 frac secs

RX Signal Power: -44.093768 dBm (N_FFt = 2048)
RX Res Signal Power: -98.570747 dBm (N_fft = 1024)
Amount of Digital SIC: 54.476979 dB

RX Signal Power: -44.232740 dBm (N_FFt = 2048)
RX Res Signal Power: -98.113147 dBm (N_fft = 1024)
Amount of Digital SIC: 53.880407 dB

RX Signal Power: -43.959299 dBm (N_FFt = 2048)
RX Res Signal Power: -93.406544 dBm (N_fft = 1024)
Amount of Digital SIC: 49.447245 dB

RX Signal Power: -44.179891 dBm (N_FFt = 2048)
RX Res Signal Power: -101.593147 dBm (N_fft = 1024)
Amount of Digital SIC: 57.413256 dB
}}}

==== In Terminal 2 (SUB-20) ====
 * Build the RF canceller configuration code (this is already done in the loaded image):
{{{
cd ~/flexicon_orbit/fd_transceiver_simple/sub20/
make
}}}
 * Check the connection to the SUB-20 device using command {{{lbusb}}}. You should see a XDIMAX devices connected to the USB hub.
 * Program and configure the RF canceller with the desired values:
{{{
cd ~/flexicon_orbit/fd_transceiver_simple/sub20/
./rf_canc_gen1_config PS-CODE ATT-CODE C1-CODE C2-CODE C3-CODE
}}}
 In particular, the {{{PS-CODE=0,1,2,...,255}}} and {{{ATT-CODE=0,1,2,...,127}}} codes are for configuring the 8-bit phase shifter and the 7-bit attenuator of the Gen-1 RF canceller, respectively. It is recommended to use {{{C1-CODE=16, C2-CODE=6, C3-CODE=6}}}, which provides 20dB isolation from the antenna-circulator interface. You can play with the values of {{{ATT}}} and {{{PS}}} until you see good cancellation profile (e.g., low residual self-interference power level) in Terminal 1.
 * An example temrinal output is below:
{{{
root@node11-10:~/flexicon_orbit/fd_transceiver_simple/sub20# ./rf_canc_gen1_config 110 30 16 6 6
Started...
Sub20 device found... Serial Number is 48AB
Device Opened!
...Finished programming DAC with value 110!
...Finished programming ATT with value 30!
...Finished programming CAP1 with value 16!
...Finished programming CAP2 with value 6!
...Finished programming CAP3 with value 6!
}}}

==== A Secondary Transmitter Using Node13-8 ====
Once the full-duplex node11-10 is up and running, you can turn on another SDR to transmit to the full-duplex node. Below, we use {{{node13-8}}} as an example in the 3rd terminal window (Terminal 3).
 * Load image, power on, and login into node13-8:
{{{
omf tell -a offh -t node13-8
omf load -i baseline-sdr.ndz -t node13-8
omf tell -a on -t node13-8
ssh root@node13-8
}}}
 * Configure the USRP Ethernet interface: {{{ifconfig eth2 192.168.10.1 netmask 255.255.255.0 up}}}
 * Set up a secondary transmitter sending a sine wave at a different frequency (e.g., 200 kHz) than that of the full-duplex node:
{{{
./tx_waveforms --args="serial=F331D4" --rate 1e6 --freq 900e6 gain 10 --wave-type SINE --wave-freq 200e3
}}}
 Now by analyzing the RX baseband data at node11-10, you will observe the received tone at 200kHz while the self-interence tone at 100kHz is cancelled to the USRP noise floor, which is around -90dBm.