[orbit-user] Unable to run AODV

[Rahul Agarwal]

Thanks for replying and looking into the matter.
We actually configured the interface 'ath0' using the iwconfig command and
then used ifconfig -a command to get the mac address of the interface of
bothe the nodes.Finally , we echoed the mac address using echo <mac address>
> /proc/net/mackill on nodes but the file remained unmodified.Then we ran
the aodvd -l -r command and got the error.

As you have pointed out , the problem may be due to unassignment of IP
address.
Also , can you please tell us how mackill works ,as no proper documentation
over mackill has been found.

On Fri, Feb 29, 2008 at 11:43 PM, Gautam D. Bhanage <
gautamb at winlab.rutgers.edu> wrote:

> The OML error seems to be because you did not assign an IP to the
> interface.
>
> You will also find a script in the image with the
> name: adhoc_configure.sh which could be used to configure the card.
> Feel free to change the parameters as per your requirement.
>
> Echoing the MAC address to the mackill files seems to be working fine with
> me.
> Please let me know the exact steps used to setup the filtering.
>
>
>
> On 2/29/08, Gautam D. Bhanage <gautamb at winlab.rutgers.edu> wrote:
> >
> > I can try and help with the Mackill part.  Can you please put in the
> > exact commands
> > you used to configure the card and setup of MAC filtering since all the
> > logs on the nodes
> > are lost after imaging.
> >
> > Thanks,
> > Gautam
> >
> >
> >
> > On 2/29/08, Rahul Agarwal <rahul.ju at gmail.com> wrote:
> >
> > > Hi all,
> > > We were trying to run aodv using aodvd command( not by scripts) as
> > > shown in Documentation section (
> > > http://www.orbit-lab.org/wiki/HowTo/UsingAODV/AODVonORBIT).
> > > As instructed we imaged the nodes of sb2 with adhoc_0.1.ndz. Then we
> > > found the mac address of interface ath0 and echoed it to the file
> > > /proc/net/mackill in respective nodes.But nothing appeared in the file
> > > . After repeated attempts , we were unable to modify /proc/net/mackill.
> > > Also , on running aodvd command (aodvd -l -r 100) , the error shown
> > > was -
> > >
> > > ERROR(oml) Could not get either OML_NAME or OML_CONFIG from env
> > > 11:03:42.670 host_init: Could not get index ofëð·]û¿
> > > : No such device
> > > 11:03:42.670 cleanup: CLEANING UP!
> > > --
> > > We were unable to make out of the error.
> > >
> > > We r in a fix as we tried 3 to 4 times on both sb1 and sb2 (using both
> > > aodvd command and corresponding ruby scripts) but could not perform the
> > > experiment.
> > > Somebody please tell us , what's going wrong and how can we run the
> > > aodv experiment flawlessly.
> > > We are genuinely in need of help.
> > >
> > > Thanks a lot,
> > > Rahul Agarwal & Ujjwal Jain
> > > Jadavpur University,
> > > Kolkata
> > > INDIA
> > >
> > > _______________________________________________
> > > orbit-user mailing list
> > > orbit-user at orbit-lab.org
> > > http://orbit-lab.org/cgi-bin/mailman/listinfo/orbit-user
> > >
> > >
> >
> >
> > --
> > --
> > Wireless Information Networking Lab
> > Rutgers, The State University of New Jersey
> > Technology Centre of New Jersey
> > 671 Route 1 South
> > North Brunswick,
> > N.J . 08902-3390.
> >
>
>
>
> --
> --
> Wireless Information Networking Lab
> Rutgers, The State University of New Jersey
> Technology Centre of New Jersey
> 671 Route 1 South
> North Brunswick,
> N.J . 08902-3390.
>
> _______________________________________________
> orbit-user mailing list
> orbit-user at orbit-lab.org
> http://orbit-lab.org/cgi-bin/mailman/listinfo/orbit-user
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://orbit-lab.org/pipermail/orbit-user/attachments/20080301/7eaf9257/attachment-0001.htm